Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
The publisher is making a number of good points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this great article followed below.
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to transform the plan of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Preparing for the Setup
Firstly, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the bathtub till the level checks out level.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and also examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub must wait up until the bath tub has actually been made use of at least once as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic person who reads about Tools You Need to Install a New Bathtub , I was thinking sharing that excerpt was a smart idea. Enjoyed reading our review? Please share it. Let other people locate it. Kudos for your time. Come back soon.
Stop the flood! Call. Report this page